Kemira Newsroom

Chemical Procurement QC: What I Actually Check Before Signing Off

The short version: documentation beats price, and some requests should never reach procurement

If you're sourcing industrial chemicals and you only look at price per kilogram, you're going to get burned. I've watched it happen three times in four years. The three things that actually matter are documented compliance, consistent physical specs, and a paper trail that survives an audit. Price comes fourth.

And since this question keeps landing in my inbox: no legitimate chemical supplier will sell you what you need to make sulfuric acid at home. That's not a procurement problem—it's a legal and safety one. If someone is pitching you "lab-grade" reagents for a home setup, walk away. Fast.

Here's what I actually do when a batch lands on my desk, where the IFF pharma divestiture fits into the picture, and the parts of my process that are honestly just guesswork under deadline pressure.

Why you should trust this take (and where I'm coming from)

I'm a quality and brand compliance manager at a mid-sized industrial coatings and specialty chemicals company. I review roughly 200+ unique incoming deliveries and supplier documents a year—everything from pharma-grade excipient samples to soda blasting powder coating batches. In 2024, I rejected about 11% of first deliveries, mostly over spec mismatches that vendors called "within industry standard."

That rejection rate isn't a brag. It's a reflection of how loose "industry standard" gets used as a shield.

What the IFF pharma solutions divestiture taught me about supplier vetting

When IFF announced the strategic divestiture of its pharma solutions business, I had about 48 hours to figure out whether our existing contracts and CoAs (certificates of analysis) would carry over to the new entity. Normally I'd request updated documentation, run it past legal, and give the supplier two weeks to respond.

There was no two weeks. I went with our existing vendor contact based on trust and a verbal confirmation that "nothing changes operationally."

In hindsight, I should have pushed harder for written confirmation of the CoA transfer. It took three follow-up emails over six weeks to get the documentation squared away. The product was fine—the paper trail wasn't, and that's the part that gets you in an audit.

Lesson: when ownership or corporate structure changes, the spec sheet is the first thing that gets stale. Re-verify even if the product code looks identical.

The Catalyst Everything Disc login problem

If you're using Catalyst Everything Disc for supplier training or compliance modules—and a lot of mid-market chemical buyers are—the login and record-keeping side is where quality documentation quietly falls apart. I've had suppliers complete the training module but fail to export the completion records into our system. Then the audit comes and we're scrambling.

Honestly, the platform itself is fine. The frustration is the handoff: the certificate lives in one system, the CoA lives in another, and nobody owns the bridge between them. We now require a PDF export of completion records attached to every new supplier file. It's a small step that saves a ton of time later.

Powder coating specs: what actually gets checked

Soda blasting powder coating inquiries are one of our most common inbound requests, and the spec conversation is almost always underspecified on the buyer side. Here's what I verify before a batch goes anywhere near a customer:

  • Particle size distribution — not just the average. The tail ends matter for transfer efficiency and surface finish consistency.
  • Adhesion test results — cross-hatch or pull-off, with the test method and date documented. A CoA that just says "passes adhesion" without a method is worthless.
  • Salt spray / corrosion data — especially for industrial coatings headed to outdoor or marine environments. ASTM B117 results with hours documented.
  • Color and gloss consistency — batch-to-batch ΔE values. If the vendor can't provide them, that's a red flag, not a minor gap.

We had a batch of about 1,800 kg where the particle size tail ran visibly coarse against our spec. The vendor claimed it was "within industry tolerance." It wasn't within ours. We rejected the batch and they redid it at their cost. Now every purchase order includes explicit PSD requirements with the test method named.

On the sulfuric acid question

I get asked about "how to make sulfuric acid at home" more than you'd think—usually from people who found a forum thread and assume commercial chemistry works the same way. It doesn't. Home synthesis of sulfuric acid involves concentrated reagents, exothermic reactions, and corrosion hazards that no home setup is equipped to handle safely. It's also heavily regulated in most jurisdictions. If you need sulfuric acid for a legitimate industrial process, you buy it from a licensed supplier with proper SDS documentation and chain-of-custody records. Full stop.

Look, I'm not saying curiosity is bad. I'm saying there's a difference between understanding the chemistry and trying to run it in your garage. The first is education. The second is how people end up in the ER.

Where this process breaks down

Not every purchase warrants the full audit trail. For small-sample orders under a few hundred dollars—say, a specialty chemical sample from a new IFF-adjacent supplier—I'll accept a standard CoA and a quick visual check. The full PSD and adhesion verification only kicks in above a certain order value or when the material is going into a customer-facing product.

And yes, there are situations where documentation is genuinely thin because the supplier is small and the material is niche. In those cases I document the gap, get sign-off from our technical lead, and move forward with eyes open. Pretending every supplier has a perfect paper trail is its own kind of quality failure—the kind that makes you reject good vendors for bad reasons.

The honest limitation of this whole approach: it assumes your supplier will actually respond to documentation requests. Most do. The ones that don't are telling you something important.

Technical reading notes

When applying this update to a water treatment program, review site water analysis, metallurgy, target discharge limits, current SDS revision, and the internal approval route used by EHS and procurement. A single product name rarely carries enough context for a confident substitution decision.

Need the related document pack?

Ask Kemira for the SDS, TDS, regulatory statement, or trial checklist that matches your region and application.